Guide · Buying and repair decisions

How much does an autoclave cost — and when is a repair worth it?

A new tabletop autoclave costs roughly $5,000 to $18,000 depending on the model and the dealer; a refurbished one a few thousand; most repairs a few hundred dollars. The autoclave cost question usually comes up because a unit just failed, so here are the real ranges side by side, and the rule of thumb we use when a customer asks whether to fix it or buy new.

Dental office sterilization counter with a tabletop autoclave and pouched instruments

New tabletop autoclaves: price by model

These are US dealer listings we checked in November 2026. They are not quotes, and the spread between dealers is wide — the same Midmark M9 showed up anywhere from about $5,500 to $14,500, depending on the listing. Treat them as a range to compare a repair against, and get a quote from your own dealer.

ModelTypeNew, typical listings
Midmark M11Automatic, 11 × 18 in chamber≈ $12,000–18,000
Midmark M9Automatic, 9 × 15 in chamber≈ $9,000–15,000
Tuttnauer 2540MManual, 10 in chamber≈ $5,500–7,600
Tuttnauer 2340MManual, 9 × 18 in chamber≈ $5,300–6,000
Tuttnauer T-Edge 10B / 11BAutomatic, Class B≈ $6,800–10,100
SciCan Statim 5000 G4Cassette≈ $6,700
SciCan Statim 2000 G4Cassette≈ $5,000–7,100

Some "new M9" listings sit well below the rest of the range. We could not tell from the listings whether those were the current model, an older one or a promotion, so ask what you are getting. Installation, a validation run and the first round of indicators are also worth asking about, because they are sometimes extra.

Refurbished units

Refurbished prices move with stock, but the listings we have seen put a refurbished Midmark M11 at roughly $3,300–5,500, an M9 around $3,400 and a demo Statim 5000 around $6,100. A small Midmark M3 showed up refurbished at about $2,800–3,500. Depot programs that rebuild your own unit and send it back run from about $1,195–1,795 at Henry Schein to $2,900–4,300 for the most complete packages we found, before shipping.

What separates a good refurbished unit from a cleaned-up one: a written warranty, a list of parts replaced (gaskets, valves, filters at minimum), a checked heater and sensors, and a cycle printout. Without those you are buying someone else's next repair.

What repairs cost

Most tabletop failures are a part, not the whole machine. Our flat prices, which include labor, ordinary parts and a test cycle:

RepairPrice
Pickup, bench diagnostic and return (credited toward the repair)$125
Door gasket replacement$249
Preventive maintenance on the bench$349
Valve, solenoid or bellowsfrom $399
Heating elementfrom $449
Control board repairfrom $449
Pump (including Statim)from $499
Control board replaced with a refurbished onefrom $899
Overhaul — Midmark M9, Tuttnauer manual$1,295
Overhaul — Midmark M11, Tuttnauer automatic, Statim$1,595

The full list, with what each line includes, is on the pricing page. Warranty: 90-day warranty on repairs, 1 year on overhauls.

Repair or replace: the rule of thumb we use

There is no formula that fits every office, but these are the questions we walk through with a customer once the diagnostic is done:

  1. Is the fault a wear part? Gaskets, filters, valves, bellows and heaters wear out on every autoclave on a schedule. Replacing them is what keeps a unit running for many years. A wear-part repair on a sound unit is almost always worth doing.
  2. Is the chamber sound? A cracked, pitted or porous chamber is the one failure that usually ends the conversation. Tuttnauer warns that a dirty chamber holding moisture against the steel eventually becomes porous; once it leaks, replacing the unit makes more sense than chasing it.
  3. How does the quote compare with a refurbished replacement? Our working line: if the repair approaches half of what a good refurbished unit of the same size costs, and the unit has other parts near the end of their life, we will tell you replacing may be the better money. Below that, repair.
  4. Is it one failure or a pattern? A unit that has had a heater, a board and a pump in two years, on clean distilled water and a proper schedule, is telling you something. A unit that failed once after years of tap water usually is not — fix it and fix the water.
  5. What does downtime cost you? Buying new means ordering, delivery and installation before you sterilize again. A repair with a loaner keeps you sterilizing on the same day the unit leaves — $149–$199 for up to 21 days, free when the repair is over $900.

For context: an overhaul of an M11 at $1,595 replaces the parts that normally wear and comes with a 1-year warranty, against roughly $3,300–5,500 for a refurbished M11 and $12,000 or more for a new one. A $249 gasket on a unit that is otherwise fine is not a reason to buy anything.

Costs people forget

  • Testing after the swap. A new or replacement unit needs the same three spore-tested empty cycles before routine use as a repaired one — see spore testing in California.
  • Consumables and maintenance. Gasket kits, filters, cleaner and distilled water cost the same whether the unit is new or old. Skipping them is what turns a cheap repair into an expensive one; see how to clean an autoclave.
  • Shipping. National mail-in depots charge shipping each way. Our pickup is included in the $125 diagnostic across Southern California.

Questions

How much does a new autoclave cost?

For the tabletop units most practices use, roughly $5,000 to $18,000 new in US dealer listings. A Tuttnauer 2340M or 2540M manual unit sits around $5,300 to $7,600, a Statim 5000 G4 around $6,700, a Midmark M9 roughly $9,000 to $15,000 and a Midmark M11 roughly $12,000 to $18,000. Prices vary a lot by dealer, promotion and package.

How much does an autoclave repair cost?

With us, a door gasket is $249, a valve or solenoid from $399, a heating element or a board repair from $449, a pump from $499 and a full overhaul $1,295 to $1,595. Pickup and bench diagnostic is $125, credited toward the repair.

Is a refurbished autoclave a good buy?

It can be, if it comes with a written warranty, a record of what was replaced and a passed test cycle. Listings we have seen put refurbished Midmark M11s around $3,300 to $5,500 and M9s around $3,400. Ask what was rebuilt; a unit that was only cleaned is not the same as one with new gaskets, valves and a checked heater.

Will you tell me if it is not worth repairing?

Yes. The diagnostic tells us what is wrong before any work starts, and if the quote does not make sense against a replacement we say so. If you decline, the $125 covers the pickup, the bench diagnostic and bringing the unit back.

Still not working?

Then the fault is inside the unit. We pick it up anywhere in Southern California, find the fault on the bench and quote it before any work — $125 for pickup, diagnostic and return, credited toward the repair. A loaner can ride along on the same stop.

Southern California pickup

Book a pickup

Tell us the model, the error on the screen and what it does. A technician reads it and texts you back with a price range and the next pickup day in your area.

  • Pickup, bench diagnostic and return — $125, credited toward the repair
  • A tested loaner swapped in on the same stop, from $149 — free on repairs over $900
  • A written quote before any work starts
  • Typical bench time: 3 to 5 business days on the bench, parts permitting

Rather talk? Call or text (424) 622-8416.