Tuttnauer Elara 11 repair
The Tuttnauer Elara 11 is a pre- and post-vacuum Class B autoclave with its own steam generator. That vacuum system is what makes it good with hollow and porous loads — and it is also what most Elara repairs come down to.
Models we see: Tuttnauer Elara 11 (Elara11), all manual revisions.
What the Elara 11 is
Per Tuttnauer's manual, the Elara 11 has an 11-inch by 19.8-inch chamber (28.5 L) fed by a separate steam generator, a vacuum pump for air removal and drying, a clean-water reservoir and a separate waste-water reservoir. It runs at 273 °F (134 °C) for unwrapped and wrapped instruments and at 250 °F (121 °C) for delicate loads, and it has a vacuum test and a Bowie-Dick program built in. It needs a 230 V supply (2300 W, 10 A) and at least 24 inches of counter depth.
The vacuum test is the most useful tool you have: the unit pulls the chamber down, closes every valve, waits five minutes and then watches the pressure for ten. A chamber that leaks air back in during that window will also fail Bowie-Dick tests and dry poorly. Run it on a dry, cool chamber — the manual suggests after a wrapped cycle and a cool-down. More on what Bowie-Dick does and does not prove is in our Bowie-Dick test guide.
What it does, what failed, what it costs
| Symptom | Usual cause | What we do | Price |
|---|---|---|---|
| Vacuum test fails or Bowie-Dick sheet shows uneven color | Air leaking in: door gasket, a valve seat, a fitting, or a weak vacuum pump | Leak traced with the chamber under vacuum, gasket, valve or pump repaired, vacuum and Bowie-Dick tests rerun | from $399 |
| Heat Time Error or slow heat-up | Steam generator element or chamber heater failing, scale in the generator, or a supply below 230 V | Heaters and supply measured, generator descaled or heater replaced | from $449 |
| Wet packs after the drying phase | Vacuum pump or air filter problem during drying, or an overloaded chamber | Pump and filter checked, drying verified on a wrapped load | from $499 |
| Steam at the door, Low Temp or Low Pressure | Worn door gasket or door not closing square | Gasket replaced, door adjusted, test cycle | from $249 |
Prices are "from", with labor, ordinary parts and a test cycle. The final price comes after the bench diagnostic, and nothing is done until you approve it. All prices →
Owner maintenance
The manual's routine: clean the door, gasket and chamber rim daily; replace the reservoir water weekly with distilled water and drain the waste reservoir at least weekly; oil the door pins; check both safety valves and clean the strainer monthly; replace the air filter every 6 months or 1,000 cycles; and inspect the door gasket every 3 months. Messages such as Heat Time Error and Low Pressure read the same as on the EZPlus units — see Tuttnauer error messages. Prices for the bench work are on the price list.
Related
Tuttnauer
2340M and 2540M, EZ9 and EZ10, 3870, Elara 11, T-Edge.
Tuttnauer T-Edge
T-Edge 10 and 11, including the Class B models.
Bowie-Dick test
What it proves, which autoclaves need it and which do not.
Tuttnauer error messages
LOW WATER, LOW HEAT, HI TEMP and the rest, explained.
Loaner autoclaves
A tested loaner swapped in on the same stop, so you never stop sterilizing.
What the price includes
- Pickup and return anywhere in our Southern California area, the bench diagnostic and a written quote — $125, credited toward the repair.
- After the repair: full cycles on the bench with a temperature and pressure check, the printout or log kept for your records.
- A loaner on the same stop if you need one — from $149, free on repairs over $900.
- 90-day warranty on repairs, 1 year on overhauls.
Questions
Is the Elara 11 a Class B autoclave?
Yes. Tuttnauer calls it a pre/post-vacuum Class B tabletop autoclave. It has its own vacuum test and Bowie-Dick programs, and a Class B unit should pass a Bowie-Dick test daily before the first load.
Will a loaner do vacuum cycles?
No — our loaners are gravity and positive-pressure units, not Class B. They sterilize solid instruments and pouches, but not the hollow and porous loads a vacuum cycle is for. Plan for that while the Elara is out, or ask us about timing so the gap is short.
Book a pickup
Tell us the model, the error on the screen and what it does. A technician reads it and texts you back with a price range and the next pickup day in your area.
- Pickup, bench diagnostic and return — $125, credited toward the repair
- A tested loaner swapped in on the same stop, from $149 — free on repairs over $900
- A written quote before any work starts
- Typical bench time: 3 to 5 business days on the bench, parts permitting
Rather talk? Call or text (424) 622-8416.