Tuttnauer error messages, explained
Tuttnauer autoclaves do not show numeric error codes. They show words — LOW WATER, LOW HEAT, HI TEMP, HI PRES, Heat Time Error — and the wording depends on the generation. Here is what each Tuttnauer error message means, what you can check yourself, and when the unit needs a bench repair.

First: which list is yours?
- E-series, EZ9 and EZ10 — short capital-letter messages on a small display (LOW WATER, HI PRES). Covers the 1730E through 3870E automatics and the original EZ units.
- EZ9Plus and EZ11Plus — full-sentence messages on a color screen ("No Water in the Chamber", "Heat Time Error"). The Elara 11 uses a very similar list.
- T-Edge 10 and 11 — touchscreen alarms, including vacuum and water-quality messages.
Manual units such as the 2340M and 2540M have no display at all; their faults show up as symptoms, covered on that page.
Checks to do before anything else
- Level the unit. A tilted unit fills unevenly, and the chamber electrode can read dry while water sits at the other end.
- Water. Drain and refill the reservoir with distilled water. Tap water scales the electrode and the fill path, which is behind many LOW WATER and ADD WATER messages.
- Clean the chamber water electrode with a damp cloth, cold and unplugged. Tuttnauer's EZPlus manual says the sides of the sensor matter more than the tip.
- Door gasket. Clean it; look for hard, flattened or torn spots. Steam leaking at the door causes low temperature and low pressure faults.
- Load. Take some instruments out. An overloaded chamber triggers heat-time and low-temp faults on all three generations.
- Power. Plug into a wall outlet, not a power strip, and switch off and on once.
If the same message comes back after that, the fault is inside the unit.
E-series, EZ9 and EZ10 messages
This list comes from a third-party summary of Tuttnauer's technician manual for the 1730E–3870E range, EZ9 and EZ10. Exact thresholds can differ by software version, so treat the numbers as typical.
| Message | What it means | Likely causes | What to do |
|---|---|---|---|
| ADD WATER | The reservoir level switch says the reservoir is low. | Reservoir really is low. If it is full: a stuck or failed float switch, its wiring, or the board input. | Top up with distilled water. If the message stays with a full reservoir, the float or wiring needs testing on the bench. |
| LOW WATER | Not enough water in the chamber during heat-up, or the chamber electrode read dry after a power failure. | Unit not level; dirty or shorted water electrode; clogged pump or fill line; air-outlet valve stuck closed; a leak at the solenoid valve, safety valve, air jet, door gasket, door bellows or a fitting. | Level the unit, refill with distilled water, clean the chamber electrode with the unit cold and unplugged. If it repeats, a leak or a fill fault needs tracing. |
| LOW HEAT | Sterilizing temperature not reached within 50 minutes (80 for the liquids cycle). | No power to the heating elements, failed elements, low line voltage, a safety thermostat opening early, clogged air jet, air valve stuck closed. | Plug straight into a wall outlet on its own circuit, not a power strip. If it still runs long, the elements and thermostat need measuring. |
| LOW TEMP | Temperature fell about 2.5 °C below the setpoint during sterilizing. | Low water, the chamber boiling dry in a long sterilize phase, thermostat or temperature sensor. | Check water and load, run again. Repeats point to a sensor, thermostat or a leak. |
| LOW PRES | Pressure fell about 4 psi below the setpoint. | Low water, elements not cycling (solid-state relay or control circuit), weak elements, pressure transducer. | Check the door gasket for steam leaks and the water level, run again; repeats need the bench. |
| HI TEMP | Temperature rose about 5 °C above the setpoint. | Elements stuck on from a shorted solid-state relay or element, or a bad temperature sensor. | Let it cool and run one more cycle. If it repeats, stop using it — this is a heater-control fault. |
| HI PRES | Pressure rose about 10 psi above the setpoint. | Elements stuck on (relay or short), or a setpoint above 274 °F. | Stop using it and have it checked; check that no one changed the cycle temperature. |
| DOOR UNLOCK | Door not closed at start, or opened during the cycle. | Door not latched, or a door switch out of adjustment. | Close the door firmly and restart. If it appears with the door shut, the switch needs adjusting. |
| POWER DN | Power was lost during the cycle and has come back. | Outlet, breaker or power cord. | Depending on the phase the cycle resumes or aborts. Treat an aborted load as not sterile and reprocess it. |
| MAN STOP, RENEW WATER, WATER INLET, CYC FINISHED | Status messages, not faults. | Cycle stopped by the user, water due for changing, filling in progress, cycle complete. | Follow the prompt — RENEW WATER means drain and refill with fresh distilled water. |
Two notes from the field. "ADD WATER" with a full reservoir is, per Tuttnauer's own support article, a stuck or defective float switch, a wiring fault or a board fault. And a forum report (unverified) ties LOW WATER at every single power-up to a dead battery on the digital board — worth mentioning to us if that is the pattern you see.
EZ9Plus and EZ11Plus messages
Summarized in our own words from section 13 of the EZPlus operator manual. Several actions mention the atmospheric pressure parameter — a stored reference the unit uses to judge pressure. The manual describes how to reset it; if you are not comfortable doing that, it is a short job on the bench.
| Message | What it means | Likely causes | What to do |
|---|---|---|---|
| Analog Input Error | A temperature or pressure sensor is disconnected or reading out of range. | Sensor, its connector or the input on the board. | Switch off and on. If it comes back, it needs service. |
| Chamber temperature not in range / Chamber pressure not in range | Chamber is hotter or colder, or above or below the pressure it should be at, before a cycle. | Unit still hot or cold from the last cycle; the stored atmospheric pressure value may need resetting. | Wait for the chamber to settle. More than about 5 minutes, or a pressure warning that will not clear, needs service or an atmospheric reset. |
| I/O Card Failed / I/O card is not connected | The I/O card is faulty or the main board lost contact with it. | I/O card, cable or main board. | Switch off and on; if it returns, it is a bench repair. |
| Low Temp | Temperature dropped below sterilizing temperature for more than a second during sterilization. | Overloaded chamber, steam leaking at the door, heater or sensor fault. | Take some load out and run a new cycle; check the gasket. Repeats need service. |
| High Temp | Temperature rose about 3 °C above sterilizing temperature for 2 seconds. | The manual points first at steam leaking around the door; on the bench we also check the heater relay and sensor. | Clean or replace the door gasket and run again. If it persists, call for service. |
| High Temp (Ending) | The chamber did not come down to the ending temperature within 10 minutes. | Exhaust path slow, sensor. | Run a new cycle; repeats need service. |
| Heat Time Error / Heat Time Error (Keep) | The chamber did not reach temperature in the preset time (or during the optional Keep Heat stage). | Overloaded chamber, atmospheric pressure setting, failing heater, low supply. | Lighten the load and run again. If it persists, the heater and settings need checking. |
| Low Pressure | Chamber pressure dropped below sterilizing pressure for 2 seconds. | Overload, steam leaking past the door gasket, valve leak. | Remove some load, check and clean the gasket, run again. |
| High Pressure | Pressure rose about 4.2 psi (29 kPa) above sterilizing pressure for 2 seconds. | Heater control or pressure sensor. | Run a new cycle; if it persists, stop and call for service. |
| High Pressure (Ending / Exhaust / Dry) | Pressure did not return close to atmospheric at the end, did not fall to its preset within 10 minutes of exhaust, or was more than about 1.5 psi over atmospheric when drying started. | Exhaust valve or strainer restriction, or an atmospheric pressure setting that needs resetting. | Clean the water outlet strainer; the atmospheric parameter can be reset per the manual. Repeats need service. |
| Pressure Time Error | Required pressure not reached in time during air removal. | Overload, leak, atmospheric setting, heater. | Lighten the load and run again; repeats need service. |
| RTC Error / Time Error | Date and time not set, or the real-time clock is faulty. | Clock not set after power loss, or a failed clock. | Set the date and time. Time Error that keeps returning is a board fault. |
| Door is open (during the cycle) | Door open or the door switch reads open mid-cycle. | Door not pushed fully closed, or a faulty door switch. | Close the door more firmly and run again; repeats need the switch checked. |
| Canceled By User / Cycle Failed | The cycle was stopped, by the user or by an error before sterilization finished. | See the second message on the screen for the reason. | Clear with START/STOP and reprocess the load — it is not sterile. |
| Air Error | Chamber did not reach atmospheric pressure within 10 minutes at the end of the cycle. | Exhaust restriction or atmospheric setting. | Wait for it to vent, reset the atmospheric pressure; if it persists, call for service. |
| Mineral free water reservoir empty | The reservoir level electrode does not sense water. | Reservoir empty; if it is full, the electrode is faulty. | Fill with distilled water. If full, switch off and on; if it stays, it needs service. |
| Power Down | Power was lost during the cycle. | Switch, cord, outlet or breaker. | Restore power and run a new cycle; reprocess the load. |
| No Water in the Chamber | The chamber electrode did not sense water within the fill time at the start of the cycle. | Empty reservoir, a dirty electrode, a clogged fill path or a failed water pump. | Fill the reservoir with distilled water and clean the water-level electrode — its sides matter more than the tip. If it continues, call for service. |
| Water in the chamber (icon), door stays locked | After the cycle the electrode still senses water, so the door stays locked. | Water did not drain back, or a dirty electrode is giving a false reading. | Do NOT force the door — water will spill out. Run a new cycle to drain the chamber, then clean the electrode. |
| Door gasket whistles | A high-pitched whistle from the door while under pressure. | Door not fully closed, dirty gasket, worn gasket, or too much lubricant at the last change. | Close the door firmly, clean the gasket. Replace it if worn, using only a thin film of silicone lubricant. |
| Water under the sterilizer | Water on the counter beneath the unit. | Overfilled reservoir draining through its overflow; if not, an internal leak. | Do not fill above the marked level or during a cycle; drain the excess. If it is not overflow, see our leak page. |
T-Edge 10 and 11 messages
From section 10 of the T-Edge 11 operator manual, summarized. The T-Edge shares the core temperature and pressure messages with the EZPlus and adds alarms for its vacuum system, pipe steam heater, clean and waste water tanks and water quality. On a Class B unit, a failing vacuum test or Bowie-Dick test is often the first sign of the same leak that later throws a vacuum time error — see the T-Edge page.
| Message | What it means | Likely causes | What to do |
|---|---|---|---|
| Vacuum time error | Vacuum did not reach its target in time, in the vacuum test or the pre-vacuum stage. | Air leaking in at the gasket, a valve or a fitting; a weak vacuum pump. | Clean the gasket, close the door firmly, run the vacuum test on a dry, cool chamber. A repeat fail is a bench repair. |
| Low Quality Water | The water-quality sensor reading is outside the limit set in the unit. | Water above the conductivity limit (the manual asks for 15 µS/cm or less), a contaminated tank. | Drain the clean-water tank, rinse and refill with fresh distilled or deionized water. |
| Not enough water detected / Water fill Error | The tank float did not change during pumping, or filling timed out. | Empty tank, stuck float switch, fill pump or line. | Fill the tank; if it is full and the message stays, the float or pump needs testing. |
| Pipe water heater / Jacket water heater temperature time error | The steam (pipe) heater or the chamber jacket heater ran more than 15 minutes without reaching temperature. | Failed heater, its relay or wiring, or scale on the steam path. | Power-cycle once. A repeat is a heater repair. |
| Chamber temperature / pressure not in range | Chamber outside its normal temperature or pressure before a cycle. | Chamber still hot, or a sensor problem. | Let it settle; if it does not, call for service. |
| Low Temp / High Temp / Low Pressure / High Pressure | Same meaning as on the EZPlus units: out of range for 1–2 seconds during sterilization. | Load, door gasket leak, heater control or sensor. | Lighten the load, check the gasket and run again; repeats need service. |
| Routine cycle service is recommended | The cycle or time counter for periodic maintenance has run out. | Not a fault — the unit is due for service. | Book the periodic service. |
| Utility issue #1 / #2 / #3 | The internal computer, its application or the I/O card dropped out, or the system clock changed mid-cycle. | Control computer, I/O card, software. | Switch the main power off and on as the screen asks. If it returns, it needs service. |
| Please fill water tank to full for start | A high-water cycle (such as prion) needs a full tank before Start appears. | Tank not full. | Fill the clean-water tank to full. |
| Time jumped during the cycle / No-user log-in / Unrecognized printer | Clock changed mid-cycle; user login required when that option is on; printer not recognized. | Settings, login option or printer connection. | Reprocess a load whose cycle had a time jump; log in; reconnect the printer. |
When it is a bench repair
Any HI TEMP or HI PRES that repeats, an Analog Input or I/O card message that survives a power-cycle, LOW WATER with a clean electrode and a level unit, or a heater time error means a part has failed. On these units that is usually a heating element (from $449), a float switch, solenoid valve or pump (from $399), a door gasket ($249) or board work (from $449). Every repair goes back with a logged test cycle. Check the price list or the model pages for the EZ9 and EZ10.
Still not working?
Then the fault is inside the unit. We pick it up anywhere in Southern California, find the fault on the bench and quote it before any work — $125 for pickup, diagnostic and return, credited toward the repair. A loaner can ride along on the same stop.
Sources
- Allclave Parts — Tuttnauer E-series / EZ9 / EZ10 display messages, citing the technician manual (third party)
- Tuttnauer EZ9Plus / EZ11Plus operation and maintenance manual, Rev V, section 13 Troubleshooting
- Tuttnauer T-Edge 11 operation and maintenance manual, Rev C, section 10
- Tuttnauer support — Add Water Fail
- Sterilizers.com tech forum — LOW WATER at every power-up (unverified)