Statim 5000 repair: Classic, 5000S and Statim 5000 G4
The Statim 5000 is the large-cassette Statim, usually a dental office's main sterilizer, and when it stops, the day stops. We repair the Statim 5000, 5000S and 5000 G4 on the bench: seal and cassette leaks, pump and steam generator faults, solenoids, check valves and controller boards.
Models we see: Statim 5000 Classic, Statim 5000S, Statim 5000 G4 (revision 7 controller).
What the Statim 5000 is
The Statim 5000 is SciCan's large-cassette steam sterilizer. Its cassette measures about 15 × 7.1 × 3 inches, big enough for full instrument cassettes, and it slides into the front of the unit like a drawer. A pump feeds distilled water into a small steam generator, the steam goes straight into the cassette, and the solenoid valve controls the exhaust to the condenser bottle. There is no door gasket and no band heater — the cassette seal and the steam generator do that job. More on the principle on our SciCan Statim page.
Three generations come through the shop, and they are not the same machine inside:
- Classic 5000 and early 5000S (from 1995) — revision 2.x/5.x or 6.x controller boards, with an aluminum or stainless steel steam generator depending on the year.
- Later 5000S — the aluminum steam generator with an external thermocouple (SciCan calls it the "ALEX" boiler, from 2005), a lower-pressure relief valve and matching software.
- Revision 7 controller units, including the Statim 5000 G4 — boards from 2007 on: all electronics on one board, a built-in service menu and NVRAM tools. The G4 adds a color display and a network connection for cycle records.
That history matters for repair. The steam generator, the board and the software revision have to match, and a part that fits a 2004 unit can be wrong for a G4.
What it does, what failed, what it costs
| Symptom | Usual cause | What we do | Price |
|---|---|---|---|
| Cycle fault 3 or 4, steam escaping at the cassette, water dripping from the drain tube | Cassette seal past 500 cycles, warped lid or damaged tray, steam tubing leak, solenoid stuck open | New seal, cassette inspected for warping, steam circuit leak-tested, full cycles logged | from $249 |
| CF1 — never reaches 95 °C; often with a big load | Very large steam leak or an overloaded cassette; or a blown thermal fuse, open steam generator or no power to it from the board | Load and seal checked first, then fuse, generator and board drive measured | from $449 |
| CF16, CF20, CF27 — steam generator overheat | Weak pump, clogged pump filters, kinked pump tube; on a G4, the reservoir float switch stuck in the raised position | Pump flow tested, filters and tube replaced, pump or float switch replaced | from $499 |
| CF10, CF11, CF15 — will not purge, vent or cool | Kinked exhaust tube, blocked cassette exhaust, solenoid stuck closed or a failed coil | Exhaust path cleared, solenoid rebuilt or replaced | from $399 |
| GFI trips at power-up, buzzing, wet air filter | Leaking check valve, dirty solenoid, failing compressor | Check valve or solenoid replaced, compressor and filters checked | from $399 |
| G4: CF94, CF95, CF96, blank or frozen color screen | Revision 7 controller board memory, display controller or the cable between them | Board, cable or display controller repaired or replaced, software restored | from $449 |
| Wraps still wet after drying | Dirty air filters, dirty cassette, drain tube with a loop or dip, stacked wraps, unit not level | Filters replaced, compressor airflow checked, drying verified on a wrapped load | from $349 |
Prices are "from", with labor, ordinary parts and a test cycle. The final price comes after the bench diagnostic, and nothing is done until you approve it. All prices →
The Statim 5000 G4: what is different
The G4 keeps the same cassette, pump, steam generator and solenoid layout, so the mechanical faults — cycle fault 3, overheat faults, exhaust blockages — are the same as on older units. What changes is the electronics and a few G4-only quirks:
- CF94, CF95 and CF96 belong to the G4: a memory fault on the revision 7 board, a lost link between that board and the color display controller, and a display program error. Sources disagree on how CF94 and CF95 are split — see the cycle fault list.
- CF16 and CF27 can be a stuck float switch. On the G4 the reservoir float can stick in the raised position, so the unit thinks it has water when it does not. If the reservoir is empty, a gentle tap on the float with a long tool can free it; if it keeps sticking, the float switch needs replacing.
- CF90 (chamber calibration lost) is first tried with a restore from the service menu's NVRAM tools, then by recalibrating the chamber thermocouple on the bench.
- No STAT-DRI. SciCan says the drying agent is not to be used on the US G4 models.
Statim 5000 maintenance, by SciCan's schedule
- Daily: distilled water in the reservoir (steam-process distilled, under about 10 µS/cm); empty the condenser bottle at each refill and keep it at the MIN line.
- Weekly: wash the cassette with a non-chlorine detergent; check the air filter and the reservoir filter.
- Every 500 cycles or 6 months: replace the cassette seal and the air / bacteria-retentive filter. On the 5000 the compressor draws through a cylindrical filter on the chassis behind the bacteria filter bracket (some compressors have none); if both are fitted, change both.
If you want it done in one go, our bench preventive maintenance is $349 with the seal, filters and a test cycle, and a Statim loaner keeps your schedule running. See all prices on the pricing page.
Related
SciCan Statim
Statim 2000 and 5000 cassette autoclaves, G4 included.
Statim cycle fault 3
The most common Statim fault and how to clear it.
Statim cycle faults
Every Statim cycle fault number and what it points to.
Statim 2000
The small-cassette Statim, G4 and earlier.
Door gasket replacement
Leaking door, steam at the seal, cycles that abort.
Loaner autoclaves
A tested loaner swapped in on the same stop, so you never stop sterilizing.
What the price includes
- Pickup and return anywhere in our Southern California area, the bench diagnostic and a written quote — $125, credited toward the repair.
- After the repair: full cycles on the bench with a temperature and pressure check, the printout or log kept for your records.
- A loaner on the same stop if you need one — from $149, free on repairs over $900.
- 90-day warranty on repairs, 1 year on overhauls.
Questions
What is the difference between the Statim 5000, 5000S and 5000 G4?
All three use the same large cassette. The S adds a pressure transducer, so it monitors pressure as well as temperature and offers more cycles (solid and hollow unwrapped, hollow wrapped, rubber and plastics, in short and extended times). The G4 is the current generation: revision 7 controller, service menu, color display and network connection.
How often does the Statim 5000 cassette seal need replacing?
SciCan says every 500 cycles or 6 months, whichever comes first, with the air filter at the same time. The seal itself is roughly $80–150 as a part; we fit it from $249 with a test cycle.
Our cassette keeps eating seals. Why?
Usually the cassette, not the seal. A lid or tray that has been dropped, warped by heat or scratched at the sealing edge will leak past any new seal. A replacement 5000 cassette is about $1,570, so we check it carefully before recommending one.
Can we get a loaner Statim 5000 while ours is repaired?
Yes — a tested Statim 5000 with its own cassette, $199 for up to 21 days, free on repairs over $900. The courier swaps it in on the same stop, so your instruments and workflow stay the same.
Should we repair it or buy a new Statim 5000 G4?
A new 5000 G4 runs about $6,700 from dealers. Seals, solenoids, pumps and boards are $249 to $899 here, and a full overhaul is $1,595. The exception is a unit that needs both a new cassette and a board — then the numbers get close, and we say so in the quote.
Sources
- SciCan Statim 2000/5000/5000S/G4 service manual 96-106775 Rev 5.0
- Statim G4 error codes sheet
- Statim error codes, revision 5XX and higher software
- Statim 5000 G4 — cassette size and new price (dealer listing)
- Statim 5000 cassette 01-101613S (parts listing)
- Statim 5000 cassette seal 01-101649S (parts listing)
Book a pickup
Tell us the model, the error on the screen and what it does. A technician reads it and texts you back with a price range and the next pickup day in your area.
- Pickup, bench diagnostic and return — $125, credited toward the repair
- A tested loaner swapped in on the same stop, from $149 — free on repairs over $900
- A written quote before any work starts
- Typical bench time: 3 to 5 business days on the bench, parts permitting
Rather talk? Call or text (424) 622-8416.