Statim cycle fault 3: why the cassette will not pressurize
Statim cycle fault 3 (CF3) means the cassette failed to build pressure and reach 110 °C in the time the software allows. On a Statim 5000 or 2000 it is the fault people ask about most, and the first suspects are the cassette seal and the cassette itself — but not the only ones. Here is how to tell, what you can check at the office, and when it needs the bench.

What cycle fault 3 means
A Statim cycle has a fixed order. Steam from the steam generator first purges the air out of the cassette while the exhaust is open. Then the solenoid valve closes the exhaust, and steam has to build pressure inside the sealed cassette until it reaches 110 °C, on its way to 134 °C (or 121 °C for rubber and plastics). The software gives that pressurizing step a time limit — on the oldest boards SciCan states it as 70 seconds. If the cassette is still short of 110 °C when the time runs out, the cycle stops with cycle fault 3, and the load is not sterile.
In plain terms: steam is going in, but it is not staying in, or the unit cannot see the temperature it expects. That is why the cause list is mostly about leaks.
The causes, from the easiest to check to the hardest
SciCan's service chart lists the same causes for CF3 on every board and software revision, and the Statim USA field sheets start with the seal and the cassette. Roughly from the outside of the unit inward:
- The cassette seal. Worn, flattened, cracked, hardened, or simply past its interval. SciCan says to replace it every 500 cycles or 6 months, whichever comes first. A busy office running a Statim as its main sterilizer gets to 500 cycles fast.
- A damaged cassette. A lid or tray that has been dropped, bent at the rim, scratched at the sealing surface or warped will leak past any seal. This is the one people miss, because a new seal fixes it for a few days and then the fault returns.
- A steam leak in the tubing. The steam circuit inside the unit has tubing and fittings between the steam generator and the cassette. A loose or cracked one lets steam out before it reaches the cassette.
- The solenoid valve stuck open. If the exhaust valve does not close, the steam goes straight out to the condenser bottle and the cassette never pressurizes. Debris on the plunger is the usual reason.
- A leaking check valve or pressure relief valve. Either one bleeds pressure out of the steam circuit. A leaking check valve can also trip the ground-fault (GFI) outlet when the unit is switched on — a useful tell.
- Probe alignment. If the thermocouple that reads the cassette is misaligned or damaged, the unit may simply not see 110 °C when it is there.
- Board reference voltage. On most software revisions SciCan has technicians check a reference voltage on the controller board; when it drifts, the temperature reading drifts with it.
What you can check at the office
- How old is the seal? If nobody remembers when it was last changed, or it has been more than 500 cycles or 6 months, change it. It is a user-replaceable part. A Statim 5000 seal costs roughly $80–150 as a part. Fit the correct seal for your cassette (2000 and 5000 seals are different), seat it evenly all the way round and keep the seal channel clean.
- Look at the cassette. With the seal out, look along the rim of the lid and the tray: dents, a bent corner, gouges on the sealing surface, a lid that rocks or does not sit flat on the tray. Any of those will keep chewing through seals. A new Statim 5000 cassette is about $1,570, so it is worth being sure before buying one — we check it on the bench.
- Watch a cycle. Run a cycle and look for steam escaping at the edges of the cassette. Water dripping from the drain tube under the unit also points at the seal or the cassette. A solenoid that clicks on and off after you remove the cassette is another sign: leaking steam gets into the cassette microswitch, and the clicking stops about a day after the leak is fixed.
- Check the water. Steam-process distilled water in the reservoir (under about 10 µS/cm), reservoir filled, condenser bottle filled to its MIN line. Water problems usually show as other faults, but rule them out.
- Check the load and the cassette fit. Do not overload the cassette, and make sure it slides fully home — you should hear the solenoid click when it goes in.
- Check the exhaust tube at the back: no kinks, and pushed fully into its fitting.
Then press STOP to reset and run an empty cycle. If it completes, run your load again and keep an eye on the next few cycles. If CF3 comes back with a new seal and a cassette that looks perfect, stop there.
When it needs the bench
Everything after the seal and the cassette is inside the unit. Testing the solenoid, finding a leak at a fitting, checking the check valve and the relief valve, the probe and the board reference voltage all mean taking the cover off, running cycles with a control box or the service menu, and on some faults recalibrating with a calibration cassette. That is our work, not the office's.
Cycle fault 3 rarely travels alone. If you have seen CF4, CF7 or CF26 on the same unit, tell us — they share most of the causes and together point the search. The full list is on our Statim cycle fault page.
What it typically costs: a seal fitted and tested from $249, a solenoid, check valve or relief valve from $399. A note on parts: SciCan asks for SciCan-approved parts to keep its safety approvals, while aftermarket seals are made to fit; we tell you which one we are quoting. If the Statim is your only sterilizer, a Statim 5000 loaner with its own cassette comes on the same stop for $199, free on repairs over $900. Model details are on the Statim 5000 and Statim 2000 pages.
Questions
We replaced the seal and still get cycle fault 3. What now?
Then the leak is somewhere else, or it is not a leak. A warped or damaged cassette will leak past a brand-new seal. If the cassette is good, the next suspects are inside the unit: a solenoid valve stuck open, a leaking check valve or pressure relief valve, steam tubing, or a misaligned thermocouple probe. All of those need the cover off.
Is cycle fault 3 the same on the Statim 2000 and the 5000?
Yes. On every Statim with CF numbers, CF3 means the cassette did not pressurize and reach 110 °C in time, and the cause list is the same. The oldest Statim 2000 units show the equivalent as "Check Cassette 3".
What is the difference between cycle fault 3 and cycle fault 4?
CF3 trips while the cassette is trying to build pressure to 110 °C. CF4 trips later, when it never reaches full sterilization conditions in time. SciCan gives them the same cause list, and you check them the same way.
Can we keep running the Statim if it only shows CF3 sometimes?
Any cycle that ends on a fault is not sterile, and intermittent CF3 usually gets worse as the seal or cassette wears. Replace the seal, and if the fault comes back, have it looked at before it starts failing every cycle.
How much does it cost to fix?
If it is the seal, from $249 with the part and a test cycle; a solenoid, check valve or relief valve from $399. The $125 pickup and bench diagnostic is credited toward the repair, and you approve the quote before any work.
Still not working?
Then the fault is inside the unit. We pick it up anywhere in Southern California, find the fault on the bench and quote it before any work — $125 for pickup, diagnostic and return, credited toward the repair. A loaner can ride along on the same stop.